Skip to main content

Error 678 or Error 796 while trying to connect internet

By Unknown
[Visit this too for a quick review Error 678 revisited]

Error 678 is an error that is reported when a remote system does not respond correctly when an attempt is made to connect to the Internet. The Error 678 message appears as “The remote computer did not respond.”

After you install Microsoft Windows XP Service Pack 2 (SP2), you may receive one of the following error messages when you try to connect to the Internet or when you try to browse the Internet.

Error 678

Error 678 "The remote computer did not respond" 

Error 769

Error 769 "The specified destination is not reachable"


Microsoft has listed following probable reasons for this error:
  1. A network cable is disconnected.
  2. The modem has been disabled.
  3. The modem drivers are corrupted.
  4. Spyware is running on the computer and is interfering with the connection.
  5. Winsock has to be repaired.
  6. Third-party firewall software is blocking the connection.

 

How to discover the cause of error 678 or error 769?

 

Step 1: Make sure the network cable is connected

Make sure that the network cable is connected to the computer and to the modem. If your computer connects to a hub or to a router, make sure the cable that connects the hub or the router to the modem is connected.

Step 2: Make sure that the network adapter is enabled

  1. Click Start, click Run, type ncpa.cpl, and then click OK.
  2. Right-click the Local Area Connection icon. Click Enable if the option is available.

 

Step 3: Reset the modem

  1. Disconnect the cable that goes from the computer to the modem.
  2. Turn off the modem. If the modem does not have a power switch, disconnect the power supply from the modem.
  3. Wait two minutes.
  4. Turn on the modem, and then connect the cable that goes from the computer to the modem.

 

Step 4: Uninstall and then reinstall the modem and the drivers by using Device Manager


Before you follow these steps, you may have to download the latest driver for your network adapter from the hardware manufacturer.
  1. Click Start, click Run, type sysdm.cpl, and then click OK.
  2. Click the Hardware tab, click Device Manager, and then locate Network Adapters.
  3. Expand Network Adapters, and then right-click the icon for your network adapter.
  4. Click Uninstall, and then click OK. In the dialog box that prompts you to remove the files that are associated with this device, click Yes.
  5. Restart the computer. Or, click Action, and then click Scan for hardware changes.
  6. If Windows finds the device but does not recognize it, you must install the latest driver for your network adapter.
If you have a Realtek 8139 network adapter, updating the driver seems to resolve this issue. For more information, visit the following Realtek Web site:
http://www.realtek.com.tw/downloads/

Step 5: Create a new DSL or cable connection

  1. Click Start, click Run, type ncpa.cpl, and then click OK.
  2. Click Create a new connection under Network Tasks. Click Next when the wizard starts.
  3. Click Connect to the Internet, and then click Next.
  4. Click Set up my connection manually, and then click Next.
  5. Select Connect using a broadband connection that requires a user name and password, and then click Next.
  6. Follow the remaining steps. Use the connection information from your Internet service provider (ISP) to complete the wizard.
Note You may have to use software that is supplied by your ISP to create the new connection.

Step 6: Repair Winsock and TCP/IP

  1. Click Start, click Run, type netsh winsock reset, and then press ENTER.
  2. When the Command Prompt window flashes, restart the computer.

    Warning Programs that access or monitor the Internet, such as antivirus, firewall, or proxy clients, may be negatively affected when you run the netsh winsock reset command. If you have a program that no longer functions correctly after you use this resolution, reinstall the program to restore functionality.

Step 7: Temporarily uninstall third-party firewalls

Some third-party firewall software such as ZoneAlarm and Norton Personal Firewall may cause Internet connectivity issues on computers that are running Windows XP SP2. You may have to temporarily uninstall these programs to test the computer. Disabling these programs may not be sufficient for testing. Make sure that you have the CD or the installation files so that you can reinstall the programs later. If these programs are causing the problem, you may have to contact the program vendor if you need help with the settings for that program.

Note You may want to verify that the Windows XP firewall is enabled before you remove the third-party firewall program.

Step 8: Scan for and remove spyware and adware

Microsoft recommends that you install Microsoft Windows Defender. To obtain Windows Defender or to obtain additional information about tools that you can use to remove unwanted software from your computer, visit the following Microsoft Web site:
http://www.microsoft.com/protect/computer/advanced/removaltools.mspx

Step 9: Clear the temporary Internet files

  1. Start Microsoft Internet Explorer.
  2. Click Tools, and then click Internet Options.
  3. On the General tab, click Delete Files.
  4. Click OK in the Delete Files dialog box, and then click OK.

Additional steps

If the problem persists after you follow the steps that are described in this article, you can try the following procedures. These procedures may help you determine the cause of the problem, or they may resolve the problem.

Repair the network connection

  1. Click Start, click Run, type ncpa.cpl, and then click OK.
  2. Right-click the icon for your connection, and then click Repair.
When you click Repair, Windows renews the IP address of your computer, and it performs other tasks that may help resolve the problem.

Renew the IP address

  1. Click Start, click Run, type command, and then click OK.
  2. Type ipconfig /renew at the command prompt, and then press ENTER.
    Information that is related to the new IP address appears in the Command Prompt window.
  3. Close the Command Prompt window.

Scan for viruses

Scan for viruses by using antivirus software. If you do not currently have an antivirus program installed on your computer, use another computer that has an Internet connection to download the installation files for an antivirus program. To download the McAfee AVERT Stinger antivirus program, visit the following McAfee Web site:
http://vil.nai.com/vil/stinger/
Test in Safe Mode
  1. Turn off the computer.
  2. Wait 10 seconds.
  3. Turn on the computer, and then immediately press F8.

    Note If you receive a keyboard error, press F1. Then, continue to press F8 one time per second.
  4. In the list, select Safe Mode with Networking.
  5. Press ENTER.

    Note: Your computer may take a longer time to start than you expect.
  6. Click OK in the dialog box that indicates that Windows is operating in Safe Mode.

Labels:

Popular posts from this blog

How to write a bach file or a batch job?

By Unknown
If your are connected with world of programming, you might have heard this word " Batch File ". A batch file is used to execute a no of operations or a list of commands one after the other often requiring no user input. A no of operations are batched in a file to be executed sequentially when we run that file. In Microsoft Windows Operating system a batch file is a file saved with .bat extension while in other operating systems like Unix and Linux it can be written as a command file shell script. Batch files are often used to load programs, run multiple processes at a time, and perform common or repetitive tasks. For example, a batch job could be used to back up many files on a computer system, process log files, run a series of calculation commands, run multiple system diagnostic processes, or any number of other things that require multiple commands to be run. A big advantage of a batch job is that it can be started at any time and left alone until t...
Read More

Adding Password to Microsoft Word Document

By Unknown
Read More

Recovering Deleted Files, Pictures & Videos

By Unknown
  So many times we accidently delete some important files, pictures or videos. Sometimes we loose files because of unexpected system failure  ( ultimately causing system format). We can get our deleted files back using Recovery Softwares/Utilities.  Even though a file was deleted there is a good chance that contents of the file are still around.  When a file is deleted the contents of the file are not removed. Only a pointer to the file in the file system table is deleted.   It is very important to immediately stop writing to the storage device that previously contained your files/pictures so that the old file contents are not overwritten.  For example, don’t take any more pictures with your digital camera because new pictures will overwrite the deleted files. HOW TO RECOVER DELETED FILES???? Step1: You will need to use a utility to recover your lost files. I like to use a free ut...
Read More